Fine Warps

There are two looms in the studio, warped, and two needing warps, it’s time to take care of this situation. Last night, I chose a weave structure from the Davidson book, yes, a “recipe,” as I’m in the mood to weave up something a bit smaller. I decided on sachets so wanted a pattern that could be varied with both treadling and color to give some variety. The back sides of the sachets will also be handwoven, most likely in plain weave. Inside will be small muslin “pillows” of dried lavender flowers.

I chose “Caroline Halvorsen’s No. 30″ on p. 44, liking the stripe design which I think will give a bit of a contemporary feel to them. I’ll be doing three repeats, using 20/2 cotton, 36 epi for this twill, so finished sachets will measure approximately 3 3/4″ square. This warp will be going on a 22” Harrisville (direct tie-up) loom.

After my last misadventure with a certain warping board, which shall go unnamed here, these warps will be made on a warping mill. This warp will be a total of 168 ends on four shafts, and I’m thinking I’d better count heddles before I start.

The second warp is for the drawloom, 20/2 cotton, 60 epi, 4 ends/dent in a 15 dent reed (I’ll need to order ASAP), or 5 ends/dent in a 12 dent reed. The warp will be 16″ wide for a total of 960 threads.

The weave structure for the drawloom will be 8 shaft satin, the warp will be threaded in straight draw 1-8 on the ground shafts, and pattern heddles will be threaded as half units, meaning each will be threaded with 4 threads, instead of 8, giving greater patterning flexibility.

Photos will be coming as I get further along. At the moment, I am paging through three large notebooks of past newsletters of both the Damask and Double Harness Study Groups of Complex Weavers, checking through some drafts/records to make sure I’m thinking this through correctly. Research.

I was going to start this tonight, but have decided to wait for daylight. I’ll bring the cone holder down, place a cone of 20/2 cotton on it, set the Ott floor lamp next to the warping mill , and start winding. I think “Last Chance Harvey” will be on, a good movie, and something to listen to while I pay attention to my crosses.

Earlier today, I went down the road and sat on a neighbor’s pier to enjoy a beautfiful, sunny afternoon in the northwoods. While sitting there, quietly, paging through the WI Sheep & Wool Festival book that arrived in the mail, I was able to quietly observe two mama ducks with their babies, three Mergansers, one loon, and several painted turtles, sunning themselves on a log my neighbor has anchored offshore for just that purpose. There was also a hawk flying over the lake, smaller birds trying to chase it away, and while that was going on, one mama duck herded her ducklings under the next pier over, and just up out of the water, out of sight. It was so enjoyable, being able to observe all these quiet daily activities of my wildlife neighbors.

3 thoughts on “Fine Warps”

  1. Both of your projects sound great! (I confess that they also sound a little intimidating to me….such fine threads.)I look forward to following them and learning more from you!!Envying your sun,Sue

  2. again your attention to detail, outstanding sense of balance, color and structure are reinforced by the knowledge that you are one girl who "does her homework"… you were a 4.0 in school now weren't you? ; ) I cannot wait to see your art!

  3. I'm trying not to think about that word, "intimidating," and just tell myself that making the warp, threading, and weaving will take a little longer. My other drawloom warp was not this fine, only 26 epi. Right now I'm wishing I were making the drawloom warp not quite so fine, because of the time crunch, but in the long run, I'll be happier with this. Onward…

Leave a reply to Life Looms Large Cancel reply